Speed Queen Fault Codes


Speed Queen Dryer Fault Codes


Alrm - Break In Alarm Door - Service door or coin vault switches.
E:00 - General Error - Re-aim micro-wand and try again.
E:01 - Proximity Error - Micro-wand is incorrectly aimed at infrared communicator. Re-aim micro-wand and try again.
E:02 - IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:05 - Invalid Value Communication - This error occurs when an invalid codes has been downloaded from the micro-wand to the electronic control. Re-aim micro-wand and try again.
E:07 - Inoperative Control - Replace control board.
E:08 - Inoperative Control - Replace control board.
E:09 - Proximity Error - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0B - IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0C -IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0F - IR Communication Programmed Off - Reprogram Infrared communicator on and manually enable IR on control. Re-aim micro-wand and try again.
E:OP - Open Temperature Sensor Error - Replace temperature sensor.
E:SH - Shorted Temperature Sensor Error - Replace temperature sensor.
EC:00 - General Communication Error - Communication problem. Try card again.
EC:02 - Time Out Error - Communication problem. Try card again.
EC:03 - Invalid Command Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:05 - Invalid or Out-Of-Range Data - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:06 - Invalid Data Code - Wrong machine type. Card my need to be replaced.
fore downloading, ensure data is current for machine type.
EC:09 - Corrupted Data Error - Communication problem. Try card again.
EC:0A - Invalid Machine Type - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:19 - No Card Reader Communication - Power down unit and power back up to try again. If error persists, reader or control board is faulty.
EC:20 - Unreadable Card - Clean chip card and card reader contacts. If error persists, card may be bad.
EC:21 - Security ID Mismatch - Wrong card. Use card with correct security code.
EC:22 - Site Code Mismatch - Wrong card. Use card with correct security code.
EC:23 - Card Maximum Value Exceeded - Use card which does not exceed maximum value.
EC:24 - Insufficient Memory On Card - Download card contents to PC and clear card for re-use.
EC:25 - Card Reader Malfunction - Card reader may need to be replaced.
EC:26 - Card Write Error - Try card again. If error persists, card may need to be replaced.
EC:27 - Diagnostic Test Card Write Failure - Card reader may need to be replaced.
EC:28 - Diagnostic Test Card Write Failure - Card reader may need to be replaced.
EC:29 - Diagnostic Test Memory Test Failure - Card reader may need to be replaced.
EC:2A - Diagnostic Test Card Interface Failure - Card reader may need to be replaced.
EC:2b - Diagnostic Test Flash Failure - Card reader may need to be replaced.
EC:2C - Bad Biberon or Non-Biberon Device - Card reader may need to be replaced.
EC:2d - Firmware Update Failed S/W (Software) Not Intact - Card reader may need to be replaced.
EC:2E - Firmware Update Failed S/W (Software) Not Intact - Card reader may need to be replaced.
EC:2F - Firmware Updates, S/W Not Intact - Card reader may need to be replaced.
EC:30 - Timeout Error - Card reader may need to be replaced.
EC:31 - Hotlisted Card Inserted Into Reader - If card is hotlisted, control will destroy card.
EC:50- - Loyalty Purse Read Error - Try card again. If error persists, card may need to be replaced.
EC:56 - Loyalty Purse Write Error - Try card again. If error persists, card may need to be replaced.
EI:00 - General Communication Error - Re-aim micro-wand and try again.
EI:01 - Bad Transmission - Re-aim micro-wand and try again.
EI:02 - Device Timeout - Re-aim micro-wand and try again.
EI:03 - Invalid Command Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:04 - Expecting Upload Request - Re-aim micro-wand and try again.
EI:05 - Invalid or Out-Of-Range Data - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:-06 - Invalid Data Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:07 - Error Writing to RTC - Control may need to be replaced.
EI:08 - Error Writing to EEPROM - Control may need to be replaced.
EI:09 - CRC-16 Error - Re-aim micro-wand and try again.
EI:0A - Invalid Machine Type / Proximity Error - Wrong machine type. Before downloading, ensure data is current for machine type. Re-aim micro-wand and try again.
EI:0F - Invalid Wake-up of IR Disabled - Manually enable IF on control and re-aim micro-wand and try again.
ERR / Err - Coin Error - Check coin drop area and remove any obstruction.
OFF - Break Down In Alarm Shutdown Error - Service door or coin vault switches.
OP - Open Thermistor - Replace thermistor.
Right Most Decimal Point Lit - Network Communication Error - Wait for error to clear. If error does not clear within one minute, disconnect the power to the unit and then power back up. If error still persists, control network board may need to be replaced.
SH - Shorted Thermistor - Replace thermistor.




Speed Queen Topload and Frontload Washer Fault Codes


Alrm - Break In Alarm Door - Service door or coin vault switches.
door - Door Open Indicator - Close door if open. If door is not open, check door switch for improper wiring.
E:00 - General Error - Re-aim micro-wand and try again.
E:01 - Proximity Error - Micro-wand is incorrectly aimed at infrared communicator. Re-aim micro-wand and try again.
E:02 - IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:05 - Invalid Value Communication - This error occurs when an invalid codes has been downloaded from the micro-wand to the electronic control. Re-aim micro-wand and try again.
E:07 - Inoperative Control - Replace control board.
E:08 - Inoperative Control - Replace control board.
E:09 - Proximity Error - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0B - IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0C -IR Communication Disconnection - Micro-wand has been removed before communication complete. Re-aim micro-wand and try again.
E:0d - Pressure Switch Error - Check fill and drain hoses for clogs or kinks and check electrical circuit. Replace in defective.
E:0F - IR Communication Programmed Off - Reprogram Infrared communicator on and manually enable IR on control. Re-aim micro-wand and try again.
E:dF - Drive Failure - Check motor and tachometer circuit open. Disconnect power and restart machine to reset.
E:dL - Door Lock Error - Open and close door. Check door lock and switches.
E:dO - Door Open During Running Cycle - Make sure door is properly closed. Check door lock and switches for defects.
E:dr - Drain Error - Maximum drain time exceeded or water is still being detected at end of spin cycle.
Edrn - Drain Error - Maximum drain time exceeded or water is still being detected at end of spin cycle.
E:FL - Fill Error - Pressure switch fails to open in 30 minutes in any fill agitate cycle.
E:HT - Heater Error - Replace bad heat circuit component.
E:OP - Open Temperature Sensor Error - Replace temperature sensor.
E:Pr - Pressure Switch Sequence Error - Replace pressure switch.
E:SH - Shorted Temperature Sensor Error - Replace temperature sensor.
E:SP - SPI Communication Error - This error is caused by transformer unplugged or wiring to motor control incorrect.
E:Ub - Unbalance Error - Redistribute load and run cycle.
EC:00 - General Communication Error - Communication problem. Try card again.
EC:02 - Time Out Error - Communication problem. Try card again.
EC:03 - Invalid Command Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:05 - Invalid or Out-Of-Range Data - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:06 - Invalid Data Code - Wrong machine type. Card my need to be replaced.
fore downloading, ensure data is current for machine type.
EC:09 - Corrupted Data Error - Communication problem. Try card again.
EC:0A - Invalid Machine Type - Wrong machine type. Before downloading, ensure data is current for machine type.
EC:19 - No Card Reader Communication - Power down unit and power back up to try again. If error persists, reader or control board is faulty.
EC:20 - Unreadable Card - Clean chip card and card reader contacts. If error persists, card may be bad.
EC:21 - Security ID Mismatch - Wrong card. Use card with correct security code.
EC:22 - Site Code Mismatch - Wrong card. Use card with correct security code.
EC:23 - Card Maximum Value Exceeded - Use card which does not exceed maximum value.
EC:24 - Insufficient Memory On Card - Download card contents to PC and clear card for re-use.
EC:25 - Card Reader Malfunction - Card reader may need to be replaced.
EC:26 - Card Write Error - Try card again. If error persists, card may need to be replaced.
EC:27 - Diagnostic Test Card Write Failure - Card reader may need to be replaced.
EC:28 - Diagnostic Test Card Write Failure - Card reader may need to be replaced.
EC:29 - Diagnostic Test Memory Test Failure - Card reader may need to be replaced.
EC:2A - Diagnostic Test Card Interface Failure - Card reader may need to be replaced.
EC:2b - Diagnostic Test Flash Failure - Card reader may need to be replaced.
EC:2C - Bad Biberon or Non-Biberon Device - Card reader may need to be replaced.
EC:2d - Firmware Update Failed S/W (Software) Not Intact - Card reader may need to be replaced.
EC:2E - Firmware Update Failed S/W (Software) Not Intact - Card reader may need to be replaced.
EC:2F - Firmware Updates, S/W Not Intact - Card reader may need to be replaced.
EC:30 - Timeout Error - Card reader may need to be replaced.
EC:31 - Hotlisted Card Inserted Into Reader - If card is hotlisted, control will destroy card.
EC:50- - Loyalty Purse Read Error - Try card again. If error persists, card may need to be replaced.
EC:56 - Loyalty Purse Write Error - Try card again. If error persists, card may need to be replaced.
EI:00 - General Communication Error - Re-aim micro-wand and try again.
EI:01 - Bad Transmission - Re-aim micro-wand and try again.
EI:02 - Device Timeout - Re-aim micro-wand and try again.
EI:03 - Invalid Command Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:04 - Expecting Upload Request - Re-aim micro-wand and try again.
EI:05 - Invalid or Out-Of-Range Data - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:-06 - Invalid Data Code - Wrong machine type. Before downloading, ensure data is current for machine type.
EI:07 - Error Writing to RTC - Control may need to be replaced.
EI:08 - Error Writing to EEPROM - Control may need to be replaced.
EI:09 - CRC-16 Error - Re-aim micro-wand and try again.
EI:0A - Invalid Machine Type / Proximity Error - Wrong machine type. Before downloading, ensure data is current for machine type. Re-aim micro-wand and try again.
EI:0F - Invalid Wake-up of IR Disabled - Manually enable IF on control and re-aim micro-wand and try again.
ERR / Err - Coin Error - Check coin drop area and remove any obstruction.
OFF - Break Down In Alarm Shutdown Error - Service door or coin vault switches.
Right Most Decimal Point Lit - Network Communication Error - Wait for error to clear. If error does not clear within one minute, disconnect the power to the unit and then power back up. If error still persists, control network board may need to be replaced.